Author |
Message |
386er
Joined: 27 Jan 2007
Posts: 274
Location: USA
|
Posted:
Thu Feb 15, 2007 2:35 am |
|
The COMPAQ DESKPRO 386, COMPAQ DESKPRO 386/20, COMPAQ DESKPRO 386/25 setup disk might work. if you have winimage than i might be able to enter the bios setup using the disk image. |
|
|
|
|
bear
Joined: 04 Oct 2004
Posts: 205
Location: 57�59'N 15�39'E
|
Posted:
Fri Feb 16, 2007 1:19 pm |
|
|
|
|
386er
Joined: 27 Jan 2007
Posts: 274
Location: USA
|
Posted:
Sun Feb 18, 2007 7:19 pm |
|
102 system board error! what the heck just happend. Anyone have any ideas to try and fix it? I NEED this computer to run or else I'm screwed!!! |
|
|
|
|
bear
Joined: 04 Oct 2004
Posts: 205
Location: 57�59'N 15�39'E
|
Posted:
Mon Feb 19, 2007 2:13 pm |
|
did the sp 0308 Work ?
I think you need to put the stuff on a bootable floppy. |
|
|
|
|
386er
Joined: 27 Jan 2007
Posts: 274
Location: USA
|
Posted:
Mon Feb 19, 2007 5:05 pm |
|
I couldn't get any floppy to work because when i put in the floppy drive controller the system dosen't want to start. I tried all kinds of controller from hdd/fdd controllers to scsi card and still have the problem. Right now I dug out an 8bit high density controller with its own bios and i hope that will work. All I just have4 to do with this machine is to get in the bios and set it to its factory settings and that should work but has proved quite challenging. |
|
|
|
|
bear
Joined: 04 Oct 2004
Posts: 205
Location: 57�59'N 15�39'E
|
Posted:
Tue Feb 20, 2007 7:01 pm |
|
Can you take hd out and copy files to it from other machine ? |
|
|
|
|
386er
Joined: 27 Jan 2007
Posts: 274
Location: USA
|
Posted:
Tue Feb 20, 2007 8:12 pm |
|
this machine will not boot to anything not evan to the harddrive. |
|
|
|
|
386er
Joined: 27 Jan 2007
Posts: 274
Location: USA
|
Posted:
Tue Feb 20, 2007 11:40 pm |
|
The highdesity floppy controler didnt work. Im gona try something welse |
|
|
|
|
386er
Joined: 27 Jan 2007
Posts: 274
Location: USA
|
Posted:
Wed Feb 21, 2007 2:32 am |
|
YES! I droped in an AMD 386 cpu and the machine started ok. I was able to access the bios and reset everything. also when i changed the cpu the little "white dots" i see on the screen where the text is is gone! The wierd noises from the floppy drives is also gone. could it just have been a bad cpu? I now have to find an intel 386 at 33mhz to replace it. My only problem now is that I can only read highdensity disk and not lowdensity ones. Anyone have any ideas?
---------------edit-------------------
The floppy controller had an lgs chip on there and that for some wierd reason would not read lowdesity disk. this system is just about fixed, now it time to hook up the harddrives! |
|
|
|
|
|